Electric Meter Bracket T200

Electric Meter Bracket T200

Details:
Our electric meter bracket T200 is a heavy‑duty, pre‑punched mounting plate specifically designed for T200‑series single‑phase and three‑phase energy meters (e.g., DDSU666, DTSU666) used in residential meter boxes, industrial distribution panels, EV charging stations, and outdoor metering cabinets. This electric meter bracket T200 is fabricated from hot‑dip galvanized steel (1.5‑2.0mm thickness) with a corrosion‑resistant zinc coating (≥5μm), passing 48h neutral salt spray test.

Send Inquiry
Description
Send Inquiry

Product Introduction

product-800-533

The Electric Meter Bracket T200 is a pre-punched steel mounting plate for T200-series single-phase and three-phase meters, used in metering cabinets, sub-metering panels and pole-mounted enclosures.

Two faults decide whether a bracket is still doing its job after ten years. It bends under the meter's weight, or the meter hangs out of square because the holes were not where the drawing said.

This plate answers both by how it is made: pressed from cold-rolled steel in a single stamping, so the holes come off the die rather than off a layout, with the T-form carrying the stiffness.

 

Technical Specifications

 

 

Item Specification
Function Pre-punched steel mounting plate for T200-series energy meters in metering enclosures
Bracket Type T-shaped; the T200 designation refers to the 200 mm standard mounting width
Base Material Cold-rolled steel sheet (SPCC)
Sheet Thickness 2.0 mm standard; 2.5 mm heavy-duty option 
Surface Treatment Option A Hot-dip galvanized, coating 65 µm and above
Surface Treatment Option B Powder coated, epoxy-polyester hybrid, 60–80 µm
Standard Colour RAL 7035 light grey, powder-coated version
Load Capacity 50 kg and above, static load test as published; test basis, duration and deflection limit are not given 
Corrosion Resistance, Hot-Dip Galvanized 500 hours neutral salt spray, no red rust (ISO 9227)
Corrosion Resistance, Powder Coated 720 hours neutral salt spray, no blistering and no red rust at the scribe (ISO 9227)
Meter Compatibility T200-series single-phase and three-phase meters, for example DDSU666 and DTSU666; direct-connected and CT-operated types
Hole Spacing 120 mm and 150 mm, single-phase direct screw mount
Three-Phase Mounting Standard 4-hole mounting pattern
Slot Adjustment Pre-punched slots allow ± 10 mm horizontal adjustment for alignment
Hole Tolerance Not published; the drawing tolerance is confirmed per order 
DIN Rail Option 35 mm DIN rail can be fitted for modular meter mounting
Fixing Method Direct screw mount, or 35 mm DIN rail where the rail option is specified
Dimension Drawing CAD / PDF outline showing all hole positions, slot lengths and overall dimensions, issued on request
Coating Reference ISO 1461 applies to the hot-dip galvanized coating and ISO 9227 is the salt spray test method
Customization Hole pattern, slot length, overall size, sheet thickness, finish and branding produced to your drawing; OEM and ODM available
Quality Control Sheet thickness, hole position and coating thickness checked on every batch
MOQ  Depends on the drawing; trial quantities for a first project are negotiable
Lead Time  7 to 10 days standard; 15 to 20 days custom
Quality Guarantee  12 to 24 months, counted from the shipment date
Manufacturing Standard  ISO 9001 quality management system
Delivery Ports  Ningbo Port / Shanghai Port
Quote Turnaround Within 24 hours of receiving the drawing

 

Core Advantages

Four things decide whether the meter is still square years after the box was built.

Hole Positions Set By The Die, Not By A Drill

Every hole and slot comes off one stamping die, so a whole batch shares a single pattern and the meters land at the same height - a straight row instead of one that drifts.

A Formed Section Takes The Load

Cold-rolled sheet at 2.0 mm, or 2.5 mm heavy-duty, is pressed to the T-form, so the profile resists bending better than a flat strip of the same gauge.

A Coating Chosen For Where The Box Stands

Outdoor, coastal and humid enclosures take the galvanized plate; indoor cabinets take the powder finish, for the cleaner RAL 7035 grey.

Alignment Carried, Not Forced

The ± 10 mm of slot travel lets the plate be lined up on the enclosure instead of having a hole filed out - the usual repair when cabinet and bracket come from two suppliers.

 

Stamped Cold-Rolled Steel Bracket vs Traditional Welded Steel Bracket

 
What Changes This Stamped Cold-Rolled Bracket Traditional Welded And Drilled Bracket
Hole pattern Set by one stamping die, so every plate in the batch matches Marked and drilled one bracket at a time
Hole position Reproducible across the batch; tolerance confirmed per order Follows the operator and the jig, if there is a jig
Stiffness Formed T-section pressed from a single sheet Flat strip, or plate welded to a separate stiffener
Joints No weld in the plate to inspect or rework Welds to check, and to dress if they move the bracket
Surface finish Coating applied after forming, over the whole part Coating burned back at the weld, then touched up by hand
Corrosion data 500 hours and 720 hours neutral salt spray published to ISO 9227 Rarely published, and hard to compare where it is
Alignment on site ± 10 mm of travel in the pre-punched slots Filed out or re-drilled to suit
Batch consistency One die, one pattern, batch after batch Bracket-to-bracket variation

 

Professional Production Process

Five steps, and each one ends in a number in the batch record. 

1

Coil is checked for grade and thickness against its mill certificate.

2

Blanking and forming run on the stamping die, so hole positions come off the tool.

3

Formed parts are gauged for hole position against the drawing before finishing.

4

Coating thickness is sampled on galvanized batches and measured on powder-coated ones.

5

Finished brackets are checked for hole position, thickness and coating, and a sample goes to salt spray to ISO 9227.

 

Material & Surface Treatment Options
 

Settle two things before the order goes in.

Galvanized Sheet Or Powder-Coated Sheet

Hot-dip galvanizing gives 65 µm and above with 500 hours of salt spray and suits coastal, humid outdoor enclosures; powder coating at 60–80 µm reaches 720 hours and carries the RAL 7035 grey.

Sheet Thickness, 2.0 mm Or 2.5 mm

The standard plate is 2.0 mm cold-rolled steel and the heavy-duty option runs 2.5 mm, for larger meters and longer unsupported spans. Thickness is a drawing call-up; send the meter mass and the span and we confirm the gauge.

 

Application Scenarios

 

Three places this plate is specified, and the finish that suits each.

Meter Box Fabrication Lines

Enclosure shops building one cabinet in volume, where a single die-set hole pattern keeps every meter at the same height.

Utility And Commercial Meter Rooms

Meter rooms and utility installations where a revenue meter has to stay square for years and still pass an inspection.

Pole-Mounted And Outdoor Metering Enclosures

Enclosures standing outdoors, where the galvanized plate is what holds up in coastal and humid air.

 

 

Frequently Asked Questions

 

 

Q: Does the 50 kg figure cover deflection, and on what basis was it measured?

A: It is a static load test result published on the page, with no method, duration or deflection limit given and no meter mass or span stated. Send both and we confirm the gauge and the deflection under load.

Q: How tight is the hole pattern?

A: It publishes the spacings, 120 mm and 150 mm for single-phase direct screw mount with a 4-hole pattern for three-phase meters, plus ± 10 mm of slot travel, but no hole tolerance - the figure a fabricator works to. Ask for the CAD outline and we confirm it.

Q: Which finish should we order for an outdoor cabinet?

A: Galvanized at 65 µm and above for outdoor, coastal and humid enclosures, at 500 hours of salt spray; powder coated at 60–80 µm for indoor cabinets, at 720 hours.

Q: Can the plate be made to our drawing, and how soon can we have a price?

A: Hole pattern, slot length, plate size, thickness, finish and branding are all produced to your drawing under OEM or ODM terms. Standard brackets leave in 7 to 10 days and made-to-drawing batches in 15 to 20, against a 12 to 24 month guarantee; send the drawing and the quantity and the price comes back within 24 hours.

 

product-3840-2160
product-3840-2160

 

 

Hot Tags: electric meter bracket t200, China electric meter bracket t200 manufacturers, suppliers, factory, busbars and brackets, Electric Meter Bracket T200

Send Inquiry
Send Inquiry