Single Pole One Inlet Five Outlet

Single Pole One Inlet Five Outlet

Details:
The Single Pole One Inlet Five Outlet is a compact and efficient single-pole power distribution block designed specifically for solar photovoltaic combiner boxes, LED lighting central control systems, industrial control panel signal and power distribution, as well as small single-phase branch circuits. This Single Pole One Inlet Five Outlet integrates one main incoming terminal with five independent outgoing branch terminals into a streamlined unit, delivering safe, reliable, and balanced power distribution for both DC and AC single-phase systems.

Send Inquiry
Description
Send Inquiry

Product Overview

product-800-533

Single Pole One Inlet Five Outlet brings one incoming conductor out to five numbered branch terminals, in a body small enough for a control box with no room to spare.

Its first job is to give the joints somewhere to live. A shallow enclosure seldom has a free run of rail, and the usual answer - a connector hanging on its conductors, or five joints made in mid-air - leaves live metal unsupported. This block fixes instead: a clip for 35 mm DIN rail, or a screw fixing to the backplate.

 

Technical Specifications

 
Item Specification
Configuration 1 pole, 1 inlet / 5 outlets
Maximum Total Input Current 125 A continuous duty, published on this page
Load Basis 125 A is the continuous rating of the block as a whole, not a simultaneous load on each of the five outlets
Rated Voltage 690 V AC
Inlet Wire Range 10 mm² – 35 mm², solid or stranded copper
Outlet Wire Range 1.5 mm² – 10 mm², solid or stranded copper
Inlet Screw M6, tightened to 5 – 7 N·m
Outlet Screw M4, tightened to 1.5 – 2.5 N·m
Conductor Tin-plated copper alloy
Conductor Scope A single-pole block carries one polarity only, one conductor per position. Tapping live and neutral therefore takes two blocks on the same circuit, and the protective earth stays on the earth bar
Housing PA66, UL94 V-0
Mounting Two fixing methods, both published here: a clip for standard 35 mm DIN rail, and a screw fixing to the panel backplate for enclosures with no rail
Circuit Identification Five numbered positions, one conductor entry each, with labelling space for the load name and custom circuit numbering
Footprint Approximately 80 mm × 45 mm × 35 mm
Protection With Cover Closed IP20 - solid objects 12.5 mm and larger are kept out, which is finger contact. Dust sealing is a separate claim and is not made here. The transparent cover is listed as optional, and no rating is published for the block without it
Operating Temperature −40 °C to +105 °C
Customization Circuit count across the series, labelling and fixing detail built to your drawing; OEM and ODM available for volume orders
MOQ 10 pieces
Lead Time 7 to 10 days standard; 15 to 20 days custom
Quality Guarantee 12 to 24 months, counted from the shipment date
Manufacturing Standard ISO 9001 quality management system
Packaging 20 pieces to a carton
Delivery Ports Ningbo Port / Shanghai Port
Quote Turnaround Within 24 hours of receiving the drawing

 

Core Advantages

Two Fixing Methods, Both Published

A rail clip and a screw fixing to the backplate are both standard, so a shallow box with no rail takes the same block as a rail-fed panel.

Five Positions Held By The Moulding

The outlets sit in one closed body, not on a strip the installer spaces out, so the gap between branches is set by the tool at every position.

A Footprint Sized For The Box

At roughly 80 by 45 by 35 mm the body is why this model sits beside the six- and eight-way versions: in a board too shallow for a longer block, it fits.

Closed, Finger-Safe, Labelled

With the optional cover shut the assembly is IP20 and fingers are kept out; without it no rating is published. Every outlet carries its own number and its own entry.

 

Mounted Distribution Block vs Loose Terminal Strip

 

The difference is less in how a screw grips a conductor than in what the joint is fixed to. 

What Changes This Five-Way Block A Loose Strip Or Loose Joint
Where it sits Clipped to 35 mm DIN rail, or screwed to the backplate Wherever the conductors happen to fall, usually unsupported
Live parts Behind one closed PA66 moulding rated UL94 V-0 Bare metal on a plastic strip, or a wrapped joint
Distance between positions Fixed by the moulding at all five outlets Set by the installer, then held by tape or by nothing
Through heat cycles The clip and screw hold the block, the moulding holds the spacing The strip relaxes and the tape dries out, so the spacing drifts
Touch protection IP20 with the optional cover closed Terminations left open, extra insulation needed
Adding a circuit later An unused position, or a second block clipped alongside The strip is cut and re-drilled
Tracing a circuit Five numbered positions with labelling space Found by tag, or by counting from the end
Landing two polarities Two blocks, one per polarity, both fed from the same circuit Mixed polarity along one strip, which is where the mistake starts

 

Professional Production Process

1

Copper bar cut, terminal seats punched to the drawing, and the cut faces deburred so a conductor meets metal.

2

Degreased, then tin plated to the drawing thickness.

3

Bodies moulded in PA66, the rail clip and screw bosses formed in the same shot.

4

All five positions checked for full screw travel, electrical results logged per batch.

 

Material & Surface Treatment Options
 

Two choices decide how this block reads after a few years in a warm box.

The Compound Behind The V-0 Grade

The body is moulded in PA66 rated UL94 V-0: the specimen self-extinguishes once the flame is removed, so a fault arc inside the box does not keep the housing burning.

Tin On The Copper Face

Contact faces are a tin-plated copper alloy, which keeps the oxide film that bare copper builds up in a warm box off both the contact face and the screw thread.

 

Application Scenarios

 

Three settings this block is built for, all short on space.

Lighting Distribution Boards

One phase fanned out to five final circuits - lighting rows, emergency lighting, a sign circuit - in a board that stays shallow.

Small Control And Equipment Boxes

Control boxes and machine panels taking a single feed out to five internal circuits, with the block screwed to the backplate.

Small Solar And Metering Enclosures

A short photovoltaic string set, or a meter box needing up to five circuits from one pole where a six- or eight-way block will not fit.

 

 

Frequently Asked Questions

 

 

Q: What is this block for?

A: It returns five branch circuits from one pole: compact lighting boards, small control boxes, short solar string sets and meter boxes needing up to five circuits.

Q: How is it fixed - does it need a DIN rail?

A: No. It clips to 35 mm DIN rail, and it can also be screwed through the body to the panel backplate. The second is what matters in a shallow box with no free rail.

Q: What are the ratings, and how much can the five outlets carry?

A: 125 A continuous for the block as a whole, on a 690 V AC rating, with the five branch circuits sharing that total. Inlet: 10–35 mm² at an M6 screw torqued to 5–7 N·m; outlets: 1.5–10 mm² at M4 torqued to 1.5–2.5 N·m.

Q: Is the block IP20 on its own, and what does UL94 V-0 cover?

A: IP20 is published with the transparent cover closed, and the cover is optional, so without it no rating applies. V-0 covers flame spread on a specimen only: it self-extinguishes once the flame is removed and drips nothing that keeps burning. Smoke tests are separate, with no report here.

Q: Can the block be produced to our own drawing and labelling?

A: Yes. Circuit count, labels and fixing detail are made to your drawing, and OEM or ODM is open on volume. Minimum order 10 pieces; standard builds 7 to 10 days, custom 15 to 20, with a quote inside 24 hours.

 

product-3840-2160
product-3840-2160

 

 

Hot Tags: single pole one inlet five outlet, China single pole one inlet five outlet manufacturers, suppliers, factory, distribution terminals, Single Pole One Inlet Eight Outlet, Single Pole One Inlet Six Outlet, Single Pole One Inlet Ten Outlet, Single Pole One Inlet Twelve Outlet, Two Inlet Four Outlet 35 To 70sqmm

Send Inquiry
Send Inquiry